FiberLaserLab

Laser Engraving Plastic: Safe and Unsafe Plastics

By FiberLaserLab Editorial Team. Updated November 18, 2026.

Quick answer

Laser engraving plastic is possible with fiber, CO2, UV and some diode lasers, depending on the plastic. Fiber lasers mark many hard plastics like ABS and polycarbonate with high contrast, CO2 lasers handle acrylic best, and UV lasers give clean, cold marks on most plastics. Only laser plastics you can identify, and never laser PVC, vinyl or PTFE.

Laser engraving plastic covers a huge range of jobs: logos on phone cases, part numbers on electronics housings, labels on tool handles, keychains and signs. But plastics are the trickiest material family to laser, because each type reacts differently, and some release dangerous gases.

This guide explains which plastics are safe, which lasers work on each, starting settings and the plastics you must never laser.

Safety first: plastics you must never laser

PlasticWhy it's dangerous
PVC (vinyl), including faux leather and many recordsReleases hydrogen chloride gas, toxic to you and corrosive to your machine
PTFE (Teflon)Releases toxic fluorine compounds
Unknown plasticsYou can't know what fumes they release

Polycarbonate is a separate case: it isn't on this list, but it burns and discolors badly when CO2 lasers try to cut it, so CO2 users usually avoid it. Fiber marking of polycarbonate is common in industry.

If you can't identify a plastic, don't laser it. Many plastics have a resin code stamped on them; when in doubt, ask the supplier for a safety data sheet. See materials never to laser.

Safety first: plastics you must never laser Plastic Why it's dangerous PVC (vinyl), including faux leather and many records Releases hydrogen chloride gas, toxic to you and corrosive to your machine PTFE (Teflon) Releases toxic fluorine compounds Unknown plastics You can't know what fumes they release
A visual recap of the section "Safety first: plastics you must never laser" above.

Which laser for which plastic?

PlasticFiberCO2UVDiode
Acrylic (PMMA)Poor on clearExcellentGoodOpaque colors only
ABSGood marksMelts, messyGoodLimited
Polycarbonate (PC)Good marks (often dark)Not recommendedGoodLimited
Polypropylene (PP)Often needs additivesMeltsGoodLimited
Polyethylene (PE, HDPE)Often needs additivesMeltsGoodLimited
Nylon (PA)Good marksMeltsGoodLimited
Laser-marking two-tone sheetGood (on suitable sheet)ExcellentGoodGood on some

Fiber lasers are widely used in industry to mark ABS, PC and nylon parts. Many industrial plastics include laser-sensitive additives to improve contrast. UV lasers mark almost any plastic with little heat, which makes them the most versatile option. See what a UV laser engraver is.

For acrylic signs and cutting, see laser engraving acrylic.

How fiber lasers mark plastic

Fiber lasers mark plastics in a few ways:

  • Carbonizing: the plastic darkens where heated, common on light plastics.
  • Foaming: the surface bubbles slightly and turns lighter, common on dark plastics.
  • Color change: pigments change color without much surface damage.
  • Engraving: material is removed, which can look rough.

MOPA lasers are especially good on plastics because shorter pulses reduce melting and give cleaner, higher-contrast marks. See what a MOPA fiber laser is.

Starting settings for fiber lasers

These are starting points for a 20W to 30W fiber laser. Plastics vary by brand and additives, so always test.

PlasticPowerSpeedFrequencyNotes
Black ABS20 to 40%1,000 to 2,000 mm/s30 to 60 kHzLight grey or white mark
White ABS30 to 50%800 to 1,500 mm/s30 to 60 kHzDarker mark, varies
Polycarbonate20 to 40%1,000 to 2,000 mm/s30 to 60 kHzOften darkens
Nylon20 to 40%800 to 1,500 mm/s30 to 60 kHzTest for melting
Two-tone engraving sheet20 to 50%1,000 to 2,000 mm/s30 to 60 kHzUse sheet rated for fiber

On a MOPA laser, try short pulse widths and higher frequencies for cleaner, less melted marks.

Tips for marking plastic

  • Start with low power. Too much heat melts the surface.
  • Test on the same part, since pigments vary between batches.
  • Use extraction. All plastic fumes should be removed.
  • Clean after marking to remove residue.
  • Keep parts flat and near the center of the lens field.

Common problems

ProblemLikely causeFix
Melted, bubbly marksToo much heatLower power, raise speed
Low contrastPlastic lacks laser additivesTry MOPA settings or a UV laser
Brown or yellow edgesBurningReduce power or pulse width
Strong smellFumes not extractedImprove extraction, check material
Mark rubs offSurface residue, not a true markAdjust settings, clean surface

Safety

Plastic fumes can be harmful even from "safe" plastics. ABS releases fumes that shouldn't be breathed, so always use extraction or vent outside. Wear glasses rated for your laser's wavelength. See laser engraver ventilation and the safety guide.

If plastic marking is a big part of your work, see our picks for the best UV laser engraver.

Frequently asked questions

Can a fiber laser engrave plastic?

Yes, many plastics, including ABS, polycarbonate and nylon. Results depend on the plastic and its additives. Never laser PVC or PTFE.

What plastic is safe to laser engrave?

Acrylic, ABS (with extraction), polycarbonate (fiber marking), nylon, and laser-rated engraving sheets are common choices. Avoid any plastic you can't identify.

Why can't you laser PVC?

PVC releases hydrogen chloride gas when lasered, which is toxic and corrodes your machine.

What is the best laser for plastic?

A UV laser marks the widest range of plastics with the least heat. A MOPA fiber laser is a strong choice for ABS, PC and nylon. CO2 is best for acrylic.

Can a CO2 laser engrave plastic?

It engraves acrylic and laser engraving sheets well, but tends to melt ABS and burn polycarbonate.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.