FiberLaserLab

Laser Engraving Acrylic: Cast vs Extruded

By FiberLaserLab Editorial Team. Updated November 17, 2026.

Quick answer

Laser engraving acrylic works best with a CO2 laser, which engraves a frosted white mark and cuts clean, flame-polished edges. Use cast acrylic for engraving and extruded acrylic for cutting. Diode and fiber lasers can't mark clear acrylic well, though they can mark some opaque colors. Ventilate well, since acrylic fumes are irritating and the material can ignite.

Laser engraving acrylic is how most custom signs, awards, LED edge-lit displays, keychains and cake toppers are made. With the right laser, acrylic engraves to a crisp frosted white and cuts with glossy, polished edges straight off the machine.

This guide covers acrylic types, which lasers work, CO2 settings, engraving and cutting tips, and safety. It's mostly about CO2 lasers, which are the standard tool for acrylic.

Cast vs extruded acrylic

TypeEngravingCuttingNotes
Cast acrylicFrosted white, high contrastGood, slightly less polished edgesBest for engraving
Extruded acrylicClear or faint engravingVery polished edges, cuts easilyBest for cutting; cheaper

If you don't know which type you have, test a small engraving: cast acrylic frosts white, extruded tends to stay clearer.

Cast vs extruded acrylic Type Engraving Cutting Notes Cast acrylic Frosted white, high contrast Good, slightly less polished edges Best for engraving Extruded acrylic Clear or faint engraving Very polished edges, cuts easily Best for cutting; cheaper
A visual recap of the section "Cast vs extruded acrylic" above.

Which lasers work on acrylic?

LaserClear acrylicColored/opaque acrylicCutting
CO2ExcellentExcellentExcellent
DiodeCan't mark or cut clearCan engrave and cut some dark, opaque colorsThin dark sheets only
FiberCan't mark clearMarks some colors and coated sheetsNo
UVFine marks on many acrylicsYesNo

Clear acrylic is transparent to diode and fiber wavelengths, so the beam passes through. See types of laser engravers and laser engraving plastic.

Starting settings for CO2 lasers

These are starting points for a 40W to 60W CO2 laser. Test on scrap of the same sheet.

JobPowerSpeedLine intervalNotes
Engrave cast acrylic15 to 30%300 to 500 mm/s0.08 to 0.1 mmFrosted white
Cut 3 mm acrylic50 to 70%10 to 20 mm/sn/aOne pass
Cut 6 mm acrylic70 to 90%4 to 10 mm/sn/aOne pass, slower
Vector line score15 to 25%100 to 300 mm/sn/aFine lines

For polished edges, use one slow, full-power pass rather than several fast ones.

Tips for clean results

  • Keep the protective film on for cutting to avoid surface marks, and peel it from the engraving area or engrave through thin paper masking.
  • Engrave the back of clear acrylic (mirrored design) for a look of depth when viewed from the front.
  • Lower air assist when cutting for shinier edges; high air assist cools the edge and can make it duller.
  • Raise the sheet on a honeycomb or pins to avoid flashback marks underneath.
  • Use vector files for clean cuts and outlines. See raster vs vector engraving.

LED edge-lit signs

Engrave the design on the back of clear cast acrylic, then mount the sheet in an LED base. The light catches the engraved areas and makes them glow. Engrave with moderate power so the frost is even.

How thick can you cut?

Cutting thickness depends mostly on CO2 tube power and lens. As a rough guide from manufacturer specs, hobby 40W to 60W machines commonly cut acrylic up to roughly 6 to 10 mm in one slow pass, while 80W to 100W and up handle thicker sheet. Thicker cuts tend to show more taper and less polished edges. Check your machine's published cutting specs, and test on an offcut first.

Common problems

ProblemLikely causeFix
Cloudy cut edgesToo fast or multiple passesOne slower pass at higher power
Flare marks on the backReflection from the bedRaise the sheet off the bed
Melted, bubbled engravingToo much powerLower power, raise speed
Faint engravingExtruded acrylicUse cast acrylic for engraving
Flames while cuttingToo slow or no air assistAdjust speed, use light air assist, never walk away

Safety

Acrylic (PMMA) is safe to laser with proper ventilation, but its fumes are irritating and it can ignite. Keep extraction running and never leave the laser unattended while cutting. Make sure the sheet really is acrylic: some plastic sheets look similar but are polycarbonate or PVC, which shouldn't be lasered. See materials never to laser and the fire safety guide.

If acrylic signs are part of your business plan, see our picks for the best CO2 laser cutter for small business.

Frequently asked questions

What laser is best for engraving acrylic?

A CO2 laser. It engraves cast acrylic to a frosted white and cuts clean, polished edges.

Can a diode laser engrave acrylic?

Not clear acrylic. It can engrave and cut some dark, opaque acrylic colors.

Can a fiber laser engrave acrylic?

Not clear acrylic. It may mark some colored or coated acrylic sheets, but CO2 lasers are far better suited.

What is the difference between cast and extruded acrylic?

Cast acrylic engraves to a bright frosted white, while extruded acrylic cuts with very polished edges but engraves less clearly.

Is it safe to laser cut acrylic?

Yes, with good ventilation and supervision. Acrylic fumes are irritating and the material can catch fire.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.