FiberLaserLab

How to Laser Engrave Glass Without Cracking It

By FiberLaserLab Editorial Team. Updated November 17, 2026.

Quick answer

To laser engrave glass, use a CO2 or UV laser, clean the glass, and cover the area with wet paper or a thin layer of dish soap to reduce chipping. Use moderate power, medium speed and a dithered or lower-resolution image, then rinse and wipe. Use a rotary for glasses and bottles, and test on a spare piece first.

Laser engraving glass gives you frosted, permanent designs on pint glasses, wine glasses, mirrors, awards and jars. This step-by-step guide shows you how to do it with a CO2 laser, the standard tool for glass, including the tricks that prevent chipping and get an even, smooth frost.

If you haven't checked whether your laser can mark glass, read can you laser engrave glass first. Fiber and diode lasers mostly can't mark clear glass.

What you need

  • A CO2 laser (or a UV laser)
  • A rotary attachment for round glasses and bottles
  • Paper towel or newspaper, water, and dish soap
  • Isopropyl alcohol or glass cleaner
  • Spare glass for testing
  • Safety glasses rated for your laser's wavelength

Step by step

1. Clean the glass

Wipe the glass with glass cleaner or alcohol to remove fingerprints and dust.

2. Prepare the design

Use a clean, high-contrast design. Large solid areas can look blotchy on glass; shapes with some texture or dithering often look better. Mirror the design if you're engraving the back of clear glass or the back of a mirror.

3. Add a cooling layer

Choose one:

  • Wet paper: lay damp paper towel or newspaper over the area, smoothing out bubbles.
  • Dish soap: brush a very thin, even layer of soap onto the surface.

Both help spread heat and reduce chipping, giving a smoother frost.

4. Set up the rotary for round items

Mount glasses on a roller or chuck rotary, level the engraving area, and enter the diameter in your software. Tapered glasses need the narrow end raised so the surface is level. See our rotary attachment guide.

5. Focus

Focus on the glass surface (or the paper surface if you're using wet paper, depending on your machine's instructions).

6. Run a test

Test on a spare glass of the same type, then engrave the real piece.

7. Clean up

Remove paper, rinse the glass and wipe it with a soft cloth.

Starting settings for CO2 lasers

These are starting points for a 40W to 60W CO2 laser. Glass types vary, so always test.

JobPowerSpeedResolution / line intervalPasses
Text and logos20 to 40%200 to 400 mm/s250 to 300 DPI1
Photos (dithered)15 to 30%300 to 500 mm/s250 to 300 DPI1
Mirror backing removal15 to 30%300 to 500 mm/s300 DPI1

Why lower resolution? Very high DPI overlaps the laser spots and overheats the glass, causing chips and an uneven frost. Moderate resolution often looks better on glass than on wood.

Starting settings for CO2 lasers Job Power Speed Resolution / line interval Passes Text and logos 20 to 40% 200 to 400 mm/s 250 to 300 DPI 1 Photos (dithered) 15 to 30% 300 to 500 mm/s 250 to 300 DPI 1 Mirror backing removal 15 to 30% 300 to 500 mm/s 300 DPI 1
A visual recap of the section "Starting settings for CO2 lasers" above.

Image tips

  • Dithering (such as Jarvis or Stucki) spreads heat and gives better tonal results than grayscale on glass.
  • Invert images when engraving from the back of clear glass so the frost reads correctly from the front.
  • Increase contrast before engraving.

See laser engraving photos for image preparation.

Engraving mirrors

You can engrave the front of a mirror like any glass, or engrave the back to remove the paint and silver layer, creating a clear design that reflects around it. Back engraving gives a striking result. Mirror the design and use low power.

Preventing chips and cracks

ProblemLikely causeFix
Chipping or flakingToo much power or DPILower power and resolution, use wet paper
Uneven, patchy frostToo much heat in solid areasUse dithering, add soap or wet paper
Cracked glassThin or tempered glass under stressLower power; avoid cheap thin glass
Faint markNot enough energySlightly raise power or slow down
Design distorted on a glassWrong rotary diameter or glass not levelRe-measure and level

UV and fiber options

UV lasers mark glass with little heat and fine detail, which suits small, detailed or industrial work. See what a UV laser engraver is. Fiber lasers can't mark clear glass directly but can remove paint from coated glass, like painted tumblers or bottles.

Safety

Wear safety glasses rated for your laser's wavelength (CO2 lasers need protection for 10,600 nm). Keep extraction running, especially when burning paper. Never leave a running laser unattended. See the laser engraver safety guide.

If you're choosing a machine for glassware, see our picks for the best CO2 laser engraver for glass.

Frequently asked questions

How do you laser engrave glass without chipping?

Use moderate power and resolution, cover the area with wet paper or a thin layer of dish soap, and use dithering for images.

What settings do I use to laser engrave glass?

On a 40W to 60W CO2 laser, start around 20 to 40% power, 200 to 400 mm/s and 250 to 300 DPI, then test.

Can you laser engrave wine glasses?

Yes, with a CO2 laser and a rotary. Thin stems and bowls need low power to avoid cracking.

Why does my laser engraved glass look patchy?

Too much heat in solid areas. Use dithering, lower resolution and a wet paper or soap layer.

Can you laser engrave the back of a mirror?

Yes. Low power removes the paint and reflective layer from the back, creating a clear design.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.