FiberLaserLab

Laser Engraving Photos: Image Prep and Settings

By FiberLaserLab Editorial Team. Updated November 19, 2026.

Quick answer

Laser engraving photos works by converting an image into dots or lines the laser can burn. Pick a high-contrast photo, crop and sharpen it, boost contrast, choose a dithering mode like Jarvis or Stucki, and set resolution to suit your laser and material. Anodized aluminum, black granite, slate, coated metal and light hardwoods give the best photo engravings.

Laser engraving photos turns pictures of pets, families and places into keepsakes on metal, stone and wood. It's one of the most rewarding jobs a laser can do, and also one of the easiest to get wrong. Most bad photo engravings come from image preparation, not the laser.

This guide covers choosing the right photo and material, editing the image, dithering, resolution and starting settings for fiber, CO2 and diode lasers.

How laser photo engraving works

A laser can't print shades of grey like an inkjet. It either marks a spot or it doesn't (or marks it a little more or less). To show tones, software converts the photo into patterns of dots, called dithering. Dense dots read as dark; sparse dots read as light. Your eye blends them into an image.

This is a raster process: the laser scans line by line across the image. See raster vs vector engraving for how raster and vector modes differ.

Best materials for photos

MaterialLaserPhoto qualityNotes
Black anodized aluminumFiber, diodeExcellentMarks light on dark; invert the image
Black graniteCO2, fiber, diodeExcellentLight marks on black; invert the image
SlateCO2, diodeGoodNatural texture limits fine detail
Black coated metal (cards, tiles)Fiber, diode, CO2Very goodLaser removes coating to reveal light metal
Maple, alder, basswoodCO2, diodeVery goodBurns dark on light; no inversion
Stainless steelFiber (MOPA best)GoodAnnealing gives grey tones
GlassCO2, UVFairFrosted look; use lower resolution

Our guide to laser engraving photos on wood covers wood in detail, and stone laser engraving covers granite and slate.

Step 1: Choose the right photo

  • Good lighting and contrast: a clear subject with distinct light and dark areas
  • Sharp focus: blurry photos get worse when engraved
  • Simple background: busy backgrounds compete with the subject
  • High resolution: at least as many pixels as your engraving will use

Close-up portraits and pet photos usually work better than wide group shots.

Step 2: Edit the image

In your photo editor or laser software:

  1. Crop to the subject.
  2. Convert to grayscale.
  3. Remove or simplify the background if it's distracting.
  4. Increase contrast and brightness. Engraved photos lose midtones, so exaggerate contrast slightly.
  5. Sharpen a little to keep edges crisp.
  6. Invert the image if the laser makes light marks on a dark material (anodized aluminum, granite, black coatings).
Step 2: Edit the image 1 Crop to the subject. 2 Convert to grayscale 3 Remove or simplify the background if it's distracting. 4 Increase contrast and brightness Engraved photos lose midtones, so exaggerate contrast slightly. 5 Sharpen a little to keep edges crisp. 6 Invert the image if the laser makes light marks on a dark material (anodized aluminum, granite, black coatings).
A visual recap of the section "Step 2: Edit the image" above.

Step 3: Choose a dithering mode

ModeLookGood for
JarvisSmooth, natural tonesMost photos on wood and stone
StuckiSimilar to Jarvis, slightly sharperPortraits and detail
Floyd-SteinbergFine, scattered dotsMetal and fine-grained materials
Ordered / HalftoneRegular dot patternStylized, newspaper look
Grayscale (power varying)Smooth gradientsSome woods with good lasers; harder to control

Test two or three modes on scrap. Different materials favor different modes.

Step 4: Set the resolution

Resolution (DPI or line interval) should match your laser's spot size and the material:

  • Too high: dots overlap and the image turns muddy and dark.
  • Too low: the image looks coarse.
Laser and materialStarting resolution
Fiber on anodized aluminum or coated metal300 to 500 DPI (hatch about 0.05 to 0.08 mm)
CO2 on granite300 to 400 DPI
CO2 on wood250 to 350 DPI
Diode on wood250 to 300 DPI
CO2 on glass200 to 300 DPI

Starting settings

These are starting points. Always test a small section of the image on scrap first.

LaserMaterialPowerSpeed
20W to 30W fiberBlack anodized aluminum20 to 40%1,500 to 3,000 mm/s
40W to 60W CO2Black granite30 to 50%200 to 400 mm/s
40W to 60W CO2Maple15 to 30%300 to 500 mm/s
10W optical diodeMaple40 to 70%3,000 to 6,000 mm/min

The fiber laser settings chart covers more metal options.

Fixing common problems

ProblemLikely causeFix
Muddy, dark imageResolution too high or too much powerLower DPI or power
Washed outToo little contrast or powerBoost contrast, raise power slightly
Negative lookImage not inverted (or inverted when it shouldn't be)Check whether the material marks light or dark
Banding linesMechanical issue or wrong intervalCheck belts (gantry) or hatch settings (galvo)
Lost detailPhoto too small or blurryUse a sharper, higher-resolution source

Software

LightBurn, EZCAD and most manufacturer apps offer dithering and image adjustments. LightBurn is popular for its image tools and preview. See LightBurn for galvo lasers and our best laser engraving software guide.

Safety

Photo engravings take longer than text, so extraction and supervision matter. Wear glasses rated for your laser's wavelength and never leave the machine unattended, especially on wood.

Frequently asked questions

Can you laser engrave a photo?

Yes. The software converts the photo into a dot pattern that the laser burns. Image preparation is the key to good results.

What is the best material for laser engraving photos?

Black anodized aluminum, black granite and light hardwoods like maple and alder give some of the best results.

What DPI should I use for laser engraving photos?

Often 250 to 400 DPI depending on your laser and material. Too high a DPI makes the image muddy.

What is the best dithering for laser photo engraving?

Jarvis and Stucki are good starting points for most materials. Test a few modes, since results vary with material.

Why does my laser engraved photo look dark?

Usually resolution or power is too high, so dots overlap. Lower the DPI or power and increase image brightness.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.