FiberLaserLab

Can a Fiber Laser Engraver Cut Metal?

By FiberLaserLab Editorial Team. Updated November 13, 2026.

Quick answer

Yes, but with limits. A desktop galvo fiber laser engraver can cut very thin metal sheet, roughly up to about 0.5 to 1 mm depending on power and metal, by running many passes. It's slow and best for small parts like jewelry blanks. Cutting thicker metal needs an industrial fiber laser cutter, a different machine with kilowatts of power and assist gas.

"Can a fiber laser cut metal?" has two very different answers depending on which fiber laser you mean. Industrial fiber laser cutters slice through thick steel plate every day. The desktop fiber engraver on a hobbyist's bench is a different tool, built for marking and engraving, and it can only cut thin sheet slowly.

This guide explains the difference, what a desktop fiber laser can realistically cut, how to do it, and when you need another tool.

Two kinds of fiber laser

Desktop fiber engraverIndustrial fiber laser cutter
Typical power20W to 100W pulsedRoughly 1,000W to well over 10,000W, continuous
Beam deliveryGalvo mirrors, fixed lens fieldCutting head on a large gantry
Assist gasNoneOxygen, nitrogen or air under pressure
Main jobMarking and engravingCutting sheet and plate
Thickness it cutsVery thin sheet, slowlyThin sheet to thick plate
Typical buyerHobbyists, small businessesFabrication shops and factories

Both use fiber laser sources at around 1064 nm, which is why metal absorbs their energy well. But a desktop engraver's short pulses are designed to remove tiny amounts of material from the surface. A cutter's continuous high power and gas jet melt and blow material out of a narrow kerf quickly.

If you're new to how galvo machines work, see what a galvo laser is.

Desktop fiber engraver vs industrial cutter Desktop engraver 20W to 100W, pulsed Galvo mirrors, fixed lens field No assist gas Marks and engraves; cuts very thin sheet, slowly Buyers: hobbyists, small shops Industrial cutter Roughly 1,000W to 10,000W+ Cutting head on a large gantry Oxygen, nitrogen or air assist Cuts thin sheet to thick plate Continuous output Buyers: fabrication shops
Why a desktop fiber engraver is not a sheet-metal cutter.

What a desktop fiber laser can cut

Cutting with a galvo fiber laser is really deep engraving that goes all the way through. The laser follows the outline again and again, removing a thin layer each pass, until the part drops out.

Rough, approximate guidance (results vary by machine, lens and metal):

PowerWhat owners commonly cutNotes
20WFoils and very thin sheetSlow; not practical for regular cutting
30WThin sheet, roughly up to a few tenths of a mmSmall parts, patience needed
50W to 60WThin sheet up to around 0.5 to 1 mm in some metalsWorkable for small parts and jewelry
100WThin sheet faster, slightly thicker in some metalsStill slow compared to a real cutter

Treat these as ballpark figures, not promises. Reflective and conductive metals such as copper, silver and gold are harder to cut than steel or aluminum of the same thickness. Our wattage guide and wattage comparison explain how power changes what's practical.

Good uses for cutting on a fiber engraver

  • Jewelry: pendants, name necklaces and earrings from thin sheet. See our jewelry engraving guide.
  • Thin shims and gaskets in metal foil
  • Small brass or stainless parts for models and crafts
  • Stencils in thin stainless sheet
  • Cutting out engraved tags from a sheet in one job

How to cut thin metal with a fiber laser

  1. Use the smallest practical lens. A 70 or 110 mm lens gives higher power density. See fiber laser lens sizes.
  2. Raise the sheet off the base with spacers so the beam can exit and debris can fall away. Use a non-flammable support.
  3. Focus on the top surface, then lower the head slightly as you cut deeper for thicker sheet.
  4. Use a vector outline, not a hatch fill. Some people add a few closely spaced parallel outlines to widen the kerf, which helps debris escape on thicker sheet.
  5. Start with high power, moderate speed and many passes, then adjust after a test.
  6. Add tabs if you don't want small parts to fall and shift mid-job.
  7. Let the part cool, then clean the edges. Expect some dross or burr on the underside.

Starting points for a 50W Q-switched fiber laser cutting thin stainless sheet (test on scrap first): power 90 to 100%, speed 300 to 800 mm/s, frequency 30 to 40 kHz, many passes until it breaks through. Lower-power machines need more passes and slower speeds.

Limits and drawbacks

  • Speed. Cutting even a small pendant can take minutes. A sheet of parts can take hours.
  • Heat. Many passes heat thin sheet. Expect discoloration and possible warping.
  • Edge quality. Edges are usually rougher than a dedicated cutter or a stamped part, with some taper.
  • Thickness ceiling. As the cut deepens, focus drift and debris slow progress. Beyond about 1 mm, it quickly becomes impractical.
  • Wear. Long jobs are fine for the laser source, but they tie up the machine you'd otherwise use for paying engraving work.

Our guide on how deep a fiber laser can engrave explains the focus drift and debris problems in more detail.

What about CO2 and diode lasers?

  • CO2 lasers are excellent cutters for wood, acrylic and leather, but standard hobby CO2 machines can't cut metal. Metal reflects most of their 10.6 µm beam. See fiber vs CO2 laser.
  • Diode lasers can't cut metal at all in any practical sense, and struggle to mark bare metal. See can a diode laser engrave metal.

Better options for cutting metal

If cutting is a regular need, consider:

NeedBetter tool
Thick sheet or plate, productionIndustrial fiber laser cutter, or a local job shop
Medium sheet, hobby or small shopPlasma cutter or CNC router with metal tooling
Thin jewelry sheet, occasionalDesktop fiber laser (50W+) or a jeweler's saw
One-off partsOnline laser cutting services

For most people buying a desktop fiber laser, cutting is a bonus, not a reason to buy. Choose the machine for its engraving ability, and treat thin-sheet cutting as a useful extra. Our list of the best fiber laser engravers for metal focuses on engraving performance.

Safety when cutting

Cutting runs longer than engraving and creates more fumes, molten spatter and hot parts. Keep extraction running, wear 1064 nm glasses with an appropriate OD rating, keep flammable materials away from the work area, and never leave a long cutting job unattended. When the beam breaks through, it can reflect off the surface below, so use a non-reflective, non-flammable support. Our laser engraver safety guide covers the essentials.

Frequently asked questions

Can a fiber laser engraver cut metal?

A desktop fiber laser engraver can cut very thin sheet by running many passes. It can't cut thick metal. That requires an industrial fiber laser cutter.

How thick can a 50W fiber laser cut?

Roughly up to around 0.5 to 1 mm in some metals, slowly. Results vary with the metal, lens and settings, so test on scrap.

Can a 20W fiber laser cut metal?

Only foils and very thin sheet, and slowly. It's not a practical cutting tool.

Can a fiber laser cut aluminum?

Thin aluminum sheet, yes, with enough power and passes. Industrial fiber cutters cut thick aluminum routinely.

Is a fiber laser better than a CO2 laser for cutting metal?

Yes. Metal absorbs the fiber laser's wavelength well, while hobby CO2 lasers can't cut metal. For wood and acrylic, CO2 is the better cutter.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.