FiberLaserLab

How Deep Can a Fiber Laser Engrave Metal?

By FiberLaserLab Editorial Team. Updated November 13, 2026.

Quick answer

A fiber laser can engrave metal from a surface mark a few microns deep to around 1 mm or more with many passes. Most marking is barely measurable, light engraving is roughly 0.05 to 0.1 mm, and deep engraving of 0.5 mm and beyond takes many passes and patience. Depth depends on power, lens, metal and time, not a fixed limit.

Fiber laser deep engraving is possible, but it isn't fast. A laser removes metal a thin layer at a time, so depth comes from repetition. The real question isn't "how deep can it go" but "how deep can it go in a time that makes sense for your job."

This guide explains realistic depths, what decides how fast you get there, starting settings, and how to keep deep engravings clean and even. If you need background on the difference between surface marks and real depth first, see laser marking vs engraving.

Typical depths at a glance

These ranges are approximate and vary with machine, lens, metal and settings.

Type of markApproximate depthTypical use
Surface marking / annealingBarely measurable (microns)Black marks, serial numbers, logos
Light engravingAround 0.05 to 0.1 mmNames and logos you can feel slightly
Medium engravingAround 0.1 to 0.3 mmTools, knives, durable ID
Deep engraving0.3 to 1 mm+Coins, dies, firearm parts, relief work, paint fill

Going past 1 mm is possible but slows down sharply and needs refocusing as you go. Most practical jobs stay under that.

What controls depth?

Power

More watts remove more material per pass. A 50W or 60W laser reaches a given depth in noticeably fewer passes than a 20W laser. Our guide to laser engraver wattage covers this, and the 20W vs 30W vs 50W vs 60W comparison shows the practical difference.

Lens size

A smaller lens concentrates the beam into a smaller spot with higher power density. For deep work, a 70 or 110 mm lens is far more efficient than a 200 or 300 mm lens. See fiber laser lens sizes.

Number of passes

Each pass removes a thin layer. Depth builds roughly with passes, until debris, focus drift and heat start to slow progress.

Material

Metals differ a lot:

  • Brass and aluminum engrave relatively quickly. See how to engrave brass and how to engrave aluminum.
  • Stainless and carbon steel are moderate.
  • Titanium and hardened tool steels are slower.
  • Gold, silver and copper are highly reflective and conductive, so they need more energy for the same depth.

Source type

Q-switched lasers with longer pulses deliver strong pulse energy, which suits material removal. MOPA lasers let you adjust pulse width, which helps with fine detail and surface finish. Both can deep engrave. Read what a MOPA laser is for the differences.

Starting settings for deep engraving

These are starting points for a 30W Q-switched fiber laser with a 110 to 150 mm lens. Test on scrap and measure depth before engraving real parts.

SettingStarting valueWhy
Power90 to 100%Maximum material removal
Speed500 to 1,000 mm/sBalance removal and heat
Frequency30 to 40 kHzHigher pulse energy
Hatch spacing0.02 to 0.03 mmEven, flat floor
Hatch angleRotate each pass (e.g. 0°, 45°, 90°, 135°)Prevents ridges
Passes10 to 100+Depth builds with passes
Cleaning passFast, low power every 10 to 20 passesRemoves debris and brightens

For lower-power lasers, slow down or add passes. For 50W and up, you can usually raise speed. Our hatch settings guide explains why rotating the hatch angle makes such a difference.

How to deep engrave step by step

  1. Clean the part with isopropyl alcohol.
  2. Focus precisely on the surface.
  3. Run a short test of 10 to 20 passes on scrap and measure the depth with calipers or a depth gauge.
  4. Estimate passes for your target depth from that test, then add a margin.
  5. Run in blocks. After every few dozen passes, stop, brush or blow out debris, and check depth.
  6. Refocus as you go. For depths beyond a few tenths of a millimeter, lower the head by roughly the depth already removed so focus stays at the bottom of the cut.
  7. Finish with a cleaning pass to smooth and brighten the floor.
How to deep engrave step by step 1 Clean the part with isopropyl alcohol. 2 Focus precisely on the surface. 3 Run a short test of 10 to 20 passes on scrap and measure the depth with calipers or a depth gauge. 4 Estimate passes for your target depth from that test, then add a margin. 5 Run in blocks After every few dozen passes, stop, brush or blow out debris, and check depth. 6 Refocus as you go For depths beyond a few tenths of a millimeter, lower the head by roughly the depth already removed so focus stays at the bottom of the cut. 7 Finish with a cleaning pass to smooth and brighten the floor.
A visual recap of the section "How to deep engrave step by step" above.

What limits deep engraving?

  • Focus drift. As the floor gets deeper, it moves away from the focal plane and each pass removes less. Refocusing helps.
  • Debris and recast. Melted metal can resolidify in the cut. Cleaning passes and air assist or extraction help.
  • Heat. Thin parts can warp, discolor or anneal. Pause between blocks to let the part cool.
  • Tapered walls. Laser engravings usually have slightly sloped side walls, so very deep, narrow features lose detail at the bottom.
  • Time. Deep engraving a large area can take a long time even on a powerful machine. Shrink the area or use a smaller lens if you can.

Common problems

ProblemLikely causeFix
Ridged or striped floorSame hatch angle every passRotate hatch angle each pass
Depth stops increasingFocus drift or debrisRefocus lower and add cleaning passes
Rough, dark floorRecast and oxide buildupAdd fast, low-power cleaning passes
Part warps or discolorsToo much heatRun in shorter blocks with cooling breaks
Uneven depth across designPart not level or near field edgeLevel the part and keep it near the center

Can a fiber laser cut instead?

At some depth, engraving becomes cutting. Desktop fiber lasers can cut through very thin sheet this way, but slowly. Our guide on whether a fiber laser can cut metal explains where the limits are.

Safety

Deep engraving runs for a long time, which means more fumes and more reflections. Keep extraction running, wear 1064 nm glasses rated for your laser, and don't leave the machine running unattended. The laser engraver safety guide covers the essentials.

If deep engraving will be a regular part of your work, consider a higher-power machine. Our picks for the best fiber laser engraver for metal cover several power levels.

Frequently asked questions

How deep can a 20W fiber laser engrave?

A 20W fiber laser can reach a few tenths of a millimeter with enough passes, and more with patience. It's much slower than a 50W laser for the same depth.

How deep can a 50W fiber laser engrave?

A 50W laser reaches 0.5 mm to around 1 mm on common metals much faster than lower-power machines. Deeper work is possible with refocusing and many passes.

Can a fiber laser engrave 1 mm deep?

Yes, on most common metals, with many passes, a small lens, rotating hatch angles and refocusing as depth increases. Expect it to take a while.

Why does my deep engraving stop getting deeper?

Usually the floor has moved out of focus or debris is building up. Lower the head to refocus, add cleaning passes and remove debris between blocks.

Is MOPA or Q-switched better for deep engraving?

Both work. Q-switched lasers deliver strong pulse energy for material removal, while MOPA lasers offer finer control over finish and detail.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.