FiberLaserLab

How to Laser Engrave a Ring (Inside and Outside)

By FiberLaserLab Editorial Team. Updated November 14, 2026.

Quick answer

Laser ring engraving uses a fiber laser with a ring chuck or rotary to turn the band under the beam, so text stays sharp around the curve. The outside is the easiest; the inside is possible on many rings with short text, a suitable fixture and careful focus. Test settings on a scrap ring of the same metal first.

Laser ring engraving is one of the most requested personalization jobs: names, dates, coordinates and short messages on wedding bands, signet rings and men's tungsten rings. It's also one of the trickiest, because a ring is small, curved and often polished.

This guide covers engraving the outside and inside of rings with a galvo fiber laser, the fixtures that make it repeatable, starting settings by metal, and the mistakes that ruin a band. For the wider picture of jewelry work, see our laser engraving jewelry guide.

What you need

  • A fiber laser. A 20W or 30W machine handles most rings. A MOPA source adds black and color marks on stainless steel and titanium.
  • A small lens, ideally 70 or 110 mm, for a fine spot. See fiber laser lens sizes.
  • A ring chuck or rotary with jaws that grip a ring from the inside or outside.
  • 1064 nm safety glasses. Polished rings reflect the beam well.
  • Scrap rings in the same metal for testing. Cheap stainless bands are ideal.

Why curved surfaces need a rotary

A galvo laser focuses on a flat plane. On a ring, only a narrow strip at the top of the band sits in focus. Move away from that strip and the surface curves away, so marks fade, widen and distort.

You have two options:

MethodHow it worksBest for
Static (no rotary)Short text kept at the top of the curveVery short marks, wide flat bands
Rotary or ring chuckThe ring turns while the laser marks one narrow strip at a timeFull names, long text, full wraps

For anything beyond a few characters, use a rotary. Our rotary attachment guide explains chuck and roller types.

How to engrave the outside of a ring

  1. Clean the ring with isopropyl alcohol.
  2. Mount it in the chuck so it runs true. A wobbly ring changes focus as it turns.
  3. Measure the diameter with calipers and enter it in the rotary settings. A wrong diameter stretches or squashes the text.
  4. Focus on the top of the band.
  5. Set the design to rotary mode in EZCAD or LightBurn, so the software splits it into narrow strips.
  6. Frame the design with the red light to check the start position.
  7. Run a test on a scrap ring, then the real piece.

Keep the text height slightly smaller than the band width so it doesn't run over the edges.

How to engrave the outside of a ring 1 Clean the ring with isopropyl alcohol. 2 Mount it in the chuck so it runs true. A wobbly ring changes focus as it turns. 3 Measure the diameter with calipers and enter it in the rotary settings. A wrong diameter stretches or squashes the text. 4 Focus on the top of the band 5 Set the design to rotary mode in EZCAD or LightBurn, so the software splits it into narrow strips. 6 Frame the design with the red light to check the start position. 7 Run a test on a scrap ring, then the real piece.
A visual recap of the section "How to engrave the outside of a ring" above.

How to engrave the inside of a ring

Inside engraving is popular for hidden messages, but it has real limits. The beam has to reach the inside surface at an angle through the ring opening, and the opposite side of the ring can block it.

What makes it work:

  • Larger ring sizes are easier. Small rings limit how far the beam can reach.
  • Short text placed near the center of the inside surface.
  • Angle the ring in a fixture so the target area faces the lens as squarely as possible, or use a chuck that holds the ring tilted.
  • Focus on the inside surface, not the top edge. This usually means lowering the head compared with outside engraving.
  • Keep the mark light. Deep engraving inside a ring is slow and can leave residue that's hard to clean.

Some machines and fixtures are designed specifically for inside ring work. If inside engraving is a big part of your business, check that capability before buying. Our picks for the best laser engraver for jewelry note which setups suit ring work.

Starting settings by ring metal

These are starting points for a 20W to 30W fiber laser with a 110 mm lens. Always test on a scrap ring of the same metal.

MetalPowerSpeedFrequencyPassesNotes
Stainless steel (light mark)50 to 70%800 to 1,500 mm/s30 to 40 kHz1Easy and forgiving
Stainless steel (black)30 to 60%100 to 300 mm/sHigh end of range1MOPA gives the darkest results
Tungsten carbide70 to 90%500 to 1,000 mm/s30 to 40 kHz1 to 3Hard; marks well, engraves slowly
Titanium40 to 70%500 to 1,500 mm/s30 to 60 kHz1Can discolor; test for color
Gold80 to 100%300 to 800 mm/s30 to 40 kHz2 to 10Reflective; needs more energy
Silver80 to 100%300 to 800 mm/s30 to 40 kHz2 to 10Marks can look faint

Gold and silver need extra care. See laser engraving gold and silver, and for darker marks on steel bands, black marking stainless steel.

Plated and coated rings

Many fashion rings are plated (gold, rose gold, black IP coating) over stainless steel or brass. The laser removes the coating where it marks, so the base metal shows. On black-coated tungsten or steel rings this creates a bright silver mark that looks great. On thin gold plating it can look like damage. Always ask what the ring is made of.

Fonts and layout

  • Use clean fonts. Simple serif and sans-serif fonts stay readable at small sizes; very thin script fonts can break up.
  • Keep text short on narrow bands.
  • Leave margins of at least a fraction of a millimeter from the band edges.
  • Single-line fonts work well for tiny inside text.

Common ring engraving problems

ProblemLikely causeFix
Text stretched or squashedWrong diameter in rotary settingsMeasure again and correct
Fades at the endsNo rotary, or text too longUse rotary mode or shorten text
Uneven depth around the bandRing not running trueRe-mount it centered
Faint mark on gold or silverNot enough energySlow down, add passes
Discoloration around textToo much heatRaise speed or lower power

Safety

Polished rings reflect the invisible 1064 nm beam strongly. Wear glasses rated for your fiber laser, keep others out of the room or use an enclosure, and run extraction to remove fumes from coatings. Our fiber laser safety glasses guide covers OD ratings.

Frequently asked questions

Can you laser engrave a ring?

Yes. A fiber laser engraves stainless steel, tungsten, titanium, gold and silver rings. A rotary or ring chuck gives the best results on curved bands.

Can a laser engrave the inside of a ring?

Often, yes, with short text, a fixture that angles the ring and careful focus on the inside surface. Small ring sizes are harder because the beam can't reach well.

Do I need a rotary to engrave rings?

For more than a few characters, yes. Without one, text fades and distorts as the band curves away from the focal plane.

Can you laser engrave tungsten rings?

Yes. Tungsten carbide marks well with a fiber laser. It's very hard, so deep engraving is slow, but surface marks are crisp.

What laser is best for ring engraving?

A fiber laser with a small lens and a ring chuck. A MOPA source is worth it if you want black or color marks on steel and titanium bands.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.