FiberLaserLab

Laser Engraving Jewelry: Rings, Pendants and Bracelets

By FiberLaserLab Editorial Team. Updated November 13, 2026.

Quick answer

Laser engraving jewelry is done with a fiber laser, which marks stainless steel, titanium, tungsten carbide, gold, silver and brass cleanly. Use a small lens for fine detail, a rotary or ring fixture for rings and bracelets, and test settings on scrap of the same metal. Be careful with plated pieces, since engraving can cut through the plating.

Laser engraving jewelry is one of the most popular uses for a fiber laser. Names on rings, coordinates on bracelets, handwriting on pendants and fingerprints on dog tags all sell well, and the items are small enough to engrave in seconds.

This guide covers which laser to use, which metals work, how to handle rings, pendants and bracelets, starting settings, fonts and the common mistakes that ruin a piece. It's aimed at hobbyists and small sellers getting into personalized jewelry.

Which laser is best for jewelry?

A fiber laser is the standard tool. Its 1064 nm wavelength is absorbed well by metals, and a galvo head delivers the fine, fast detail jewelry needs.

LaserJewelry use
Fiber (Q-switched)Excellent for engraving names, dates and logos on most metals
Fiber (MOPA)Everything above, plus finer control, darker marks and color on stainless and titanium
DiodeCoated or anodized pieces only; poor on bare precious metals
CO2Wood, leather and acrylic jewelry; not bare metal
UVVery fine marks on some materials; less common for metal jewelry

A 20W or 30W fiber laser handles most jewelry. MOPA is worth it if you want black or color marks on stainless and titanium. See what a MOPA fiber laser is and color marking stainless steel.

Jewelry metals and how they engrave

MetalHow it engravesNotes
Stainless steelEasy; white, black or deep marksMost forgiving metal for beginners
TitaniumGood; can produce colors with the right settingsSee laser engraving titanium
Tungsten carbideMarks wellVery hard, so deep engraving is slow
GoldEngraves well with more energyHighly reflective; test carefully. See engraving gold and silver
Sterling silverEngraves, but reflective and conductiveMarks can look faint; oxidizing finishes add contrast
Brass and copperEngrave wellSee how to engrave brass and copper
Plated jewelryThe laser removes platingThe base metal shows through; warn customers
Anodized aluminumBright white marksLightweight fashion pieces and tags

Plated and filled jewelry: read this first

A lot of fashion jewelry is gold-plated, rhodium-plated or PVD-coated over brass or stainless steel. Engraving removes the coating in the marked area, exposing the base metal. Sometimes that's the look you want; sometimes it ruins the piece.

  • Ask what the piece is made of before engraving a customer's item.
  • Test on an identical blank if possible.
  • Use light, fast settings if you only want to mark the surface layer.
  • Gold-filled pieces have a thicker gold layer than plating, but deep engraving can still expose the base.

Choosing the right lens

Jewelry is small, and fine detail needs a small spot. A 70 mm or 110 mm lens is ideal. Larger lenses spread the beam and soften tiny text. Our guide to fiber laser lens sizes explains why.

Engraving rings

Rings are the most requested jewelry job, and the trickiest:

  • Outside of rings: use a rotary or ring chuck so the surface rotates under the beam. Without one, text on a curved band distorts and fades at the ends.
  • Inside of rings: possible on many rings with the right fixture, a short design and careful focus, but small rings limit the angle the beam can reach.
  • Tungsten and titanium bands are popular for engraved men's rings.

Our dedicated guide on how to engrave a ring inside and outside covers the full process. The rotary attachment guide explains ring chucks and roller rotaries.

Engraving pendants, tags and charms

Flat pieces are the easiest place to start:

  1. Clean the piece with isopropyl alcohol.
  2. Hold it flat with a simple jig, tape or a fixture plate. Small pieces move easily.
  3. Focus on the surface.
  4. Frame the design with the red preview light.
  5. Engrave, then clean and inspect.

For batches, a jig that holds several identical blanks saves a lot of time. Dog tags follow the same workflow; see laser engraving dog tags.

Engraving pendants, tags and charms 1 Clean the piece with isopropyl alcohol. 2 Hold it flat with a simple jig, tape or a fixture plate. Small pieces move easily. 3 Focus on the surface. 4 Frame the design with the red preview light. 5 Engrave, then clean and inspect.
A visual recap of the section "Engraving pendants, tags and charms" above.

Engraving bracelets and cuffs

  • Flat bar bracelets: engrave like pendants, with the bar held level.
  • Cuffs and bangles: curved surfaces need a rotary, or short designs kept near the top of the curve where focus is consistent.
  • Inside of cuffs: popular for hidden messages. Open cuffs give the beam better access than closed bangles.

Starting settings for jewelry

These are starting points for a 20W to 30W Q-switched fiber laser with a 110 mm lens. Always test on scrap of the same metal first.

JobPowerSpeedFrequencyHatch spacingPasses
Stainless, light mark50 to 70%1,000 to 2,000 mm/s30 to 40 kHz0.02 to 0.03 mm1
Stainless, black mark30 to 60%100 to 300 mm/sHigh end of your range0.01 to 0.02 mm1
Gold or silver, engrave80 to 100%300 to 800 mm/s30 to 40 kHz0.02 mm2 to 10
Brass, engrave70 to 90%500 to 1,000 mm/s30 to 40 kHz0.02 to 0.03 mm1 to 5
Tungsten, mark70 to 90%500 to 1,000 mm/s30 to 40 kHz0.02 mm1 to 3

For black marks on stainless, also see how to laser engrave stainless steel.

Fonts and design tips

  • Keep text large enough. Very small text blurs or fills in. Test your minimum size on scrap; many engravers find text around 1 mm tall is the practical lower end for crisp results.
  • Use clean fonts. Simple sans-serif and clear script fonts engrave better than thin, ornate ones.
  • Single-line fonts work well for tiny text, since the laser traces one line instead of filling a shape.
  • Handwriting and fingerprints: scan at high resolution, clean up in design software and convert to vector where possible.
  • Mind the curve. On rings, keep text short enough that it doesn't wrap too far around the band without a rotary.

Common jewelry engraving mistakes

  • Engraving through plating without telling the customer
  • Using a large lens and getting soft, faint text
  • Skipping the test piece on precious metal
  • Letting small pieces move during the job
  • Overheating thin pieces, causing discoloration or warping
  • Ignoring reflections. Polished gold and silver reflect strongly; always wear 1064 nm glasses

Safety

Fiber lasers are Class 4 lasers with an invisible beam, and polished jewelry reflects it well. Wear safety glasses rated for 1064 nm, use an enclosure if others are nearby, and ventilate fumes, especially from plated or coated pieces. The fiber laser safety glasses guide explains OD ratings.

Choosing a machine for jewelry

For jewelry, prioritize a small lens, a quality rotary or ring chuck, and a MOPA source if you want color or black marks. Our picks for the best laser engraver for jewelry compare machines with these features, and the best MOPA fiber lasers cover color-capable options.

Frequently asked questions

What laser is best for engraving jewelry?

A fiber laser. A 20W or 30W machine handles most jewelry, and a MOPA fiber laser adds black and color marks on stainless steel and titanium.

Can you laser engrave gold and silver jewelry?

Yes, with a fiber laser. Gold and silver are reflective and conductive, so they need more energy and careful testing on scrap first.

Can you laser engrave plated jewelry?

Yes, but the laser removes the plating where it marks, exposing the base metal. Test on an identical piece and tell customers what to expect.

Can you laser engrave the inside of a ring?

Often, yes, with a suitable fixture, short text and careful focus. Very small rings are harder because the beam can't reach the inside at a good angle.

What size text can a fiber laser engrave on jewelry?

Very small text is possible with a small lens and good focus. Test your minimum size on scrap; around 1 mm tall is a common practical lower limit for crisp lettering.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.