FiberLaserLab

How to Laser Engrave Brass and Copper

By FiberLaserLab Editorial Team. Updated November 14, 2026.

Quick answer

To laser engrave brass, use a fiber laser, clean the surface, focus accurately and run a test grid. Brass engraves readily and can give light, dark or deep marks depending on speed and passes. Copper is more reflective and conductive, so it needs more energy, slower speeds or a higher-power or MOPA laser. Seal or polish afterward to keep the result looking good.

Brass is one of the nicest metals to laser engrave. It takes clean, detailed marks, engraves to depth faster than stainless steel, and looks great on nameplates, plaques, knife bolsters, bullet casings and gifts. Copper is its trickier cousin: beautiful, but more reflective and harder to mark.

This guide shows you how to laser engrave brass and copper with a fiber laser, with starting settings, finishing tips and fixes for common problems. If you're brand new to fiber lasers, read how to use a laser engraver first.

Can you laser engrave brass?

Yes. Brass is an alloy of copper and zinc that absorbs a fiber laser's 1064 nm wavelength well enough to mark and engrave easily. Diode and CO2 lasers struggle on bare brass, though they can mark coated or painted brass. See can a diode laser engrave metal for why.

LaserBare brassBare copper
Fiber (Q-switched)Very goodFair to good, needs more energy
Fiber (MOPA)Very good, more finish controlGood
DiodePoor without marking sprayPoor
CO2Needs marking sprayNeeds marking spray
Can you laser engrave brass? Laser Bare brass Bare copper Fiber (Q-switched) Very good Fair to good, needs more energy Fiber (MOPA) Very good, more finish control Good Diode Poor without marking spray Poor CO2 Needs marking spray Needs marking spray
A visual recap of the section "Can you laser engrave brass?" above.

Brass vs copper: why they behave differently

  • Brass reflects less and conducts heat less than pure copper, so the laser's energy stays where it lands. Marks form quickly.
  • Copper is highly reflective at 1064 nm and spreads heat away fast. Much of the energy bounces or dissipates, so marks need more power, slower speed or more passes.

Higher-power lasers (30W and up) and MOPA sources help noticeably on copper. Our dedicated guide to laser engraving copper covers it in more depth.

Step by step

1. Clean the surface

Brass is often lacquered or oily. Wipe with isopropyl alcohol. If the piece has a clear lacquer, the laser will remove it in the marked area, which is fine, but residue may need cleaning afterward.

2. Focus precisely

Reflective metals punish poor focus. Use your focus gauge or red-dot method and check it twice. See how to focus a fiber laser.

3. Run a test grid

Test a grid of power and speed values on scrap. Brass can produce a range of finishes, from bright and light to dark brown or nearly black, so the grid shows you which look each setting gives.

4. Starting settings

These are starting points for a 30W Q-switched fiber laser with a 110 to 150 mm lens. Test before engraving real items.

FinishPowerSpeedFrequencyHatch spacingPasses
Brass, light mark60 to 80%800 to 1,500 mm/s30 to 40 kHz0.03 mm1
Brass, dark mark30 to 50%200 to 500 mm/s50 to 80 kHz0.02 mm1
Brass, deep engrave90 to 100%500 to 1,000 mm/s30 to 40 kHz0.02 to 0.03 mm10 to 30+
Copper, mark90 to 100%200 to 600 mm/s30 to 40 kHz0.02 mm2 to 5

More materials are in our fiber laser settings chart.

5. Clean and finish

After engraving, wipe away residue. For a bright engraving on polished brass, a light buff with fine polish restores the surface. For long-term shine, a clear lacquer or wax protects against tarnish.

Getting dark marks on brass

Dark marks come from heating the surface rather than removing it. Slower speed, lower power, higher frequency and tight hatch spacing are the usual recipe. MOPA lasers give more control here because you can adjust pulse width. Test carefully: too much heat makes marks blotchy.

Deep engraving brass

Brass is one of the faster metals to deep engrave. Rotate the hatch angle each pass, add a fast cleaning pass every 10 to 20 passes, and refocus as depth increases. Our guide to how deep a fiber laser can engrave explains the process. Deep engravings on brass plaques can be paint-filled for contrast.

  • Nameplates, plaques and trophy plates
  • Knife bolsters and pommels (see laser engraving knives)
  • Jewelry, charms and keychains (see the jewelry engraving guide)
  • Shell casings and keepsakes
  • Copper mugs and decor
  • Musical instrument parts

Common problems

ProblemLikely causeFix
Very faint markToo fast, or out of focusSlow down, check focus
Blotchy dark areasToo much heatRaise speed or reduce power
Mark tarnishes quicklyExposed fresh metal oxidizesSeal with lacquer or wax
Nothing marks on copperNot enough energy densitySlow down, add passes, use a small lens
Residue in engravingLacquer or debrisClean with alcohol, add a cleaning pass

Safety

Brass and copper reflect the invisible fiber beam strongly, especially when polished. Wear 1064 nm glasses rated for your laser, and keep extraction running: lacquers and coatings produce fumes, and fine metal particles shouldn't be inhaled. Our laser engraver safety guide covers the essentials.

If you mostly engrave reflective metals like copper, a higher-power or MOPA machine pays off. Our best MOPA fiber laser picks explain the options.

Frequently asked questions

Can you laser engrave brass?

Yes, with a fiber laser. Brass marks and engraves easily, and can produce light, dark or deep finishes depending on settings.

What laser is best for engraving brass?

A fiber laser. A 20W to 30W machine handles most brass jobs, and higher power speeds up deep engraving.

Why is copper hard to laser engrave?

Copper reflects much of a fiber laser's light and conducts heat away quickly. It needs more power, slower speeds or a MOPA laser.

Can a diode laser engrave brass?

Not bare brass in any practical way. It can mark painted or coated brass, or use marking spray on bare brass.

How do I stop engraved brass from tarnishing?

Clean it, then apply a clear lacquer or wax. Freshly exposed brass oxidizes over time without protection.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.