Laser Engraving Gold and Silver: What Works
Quick answer
Laser engraving gold and silver is done with a fiber laser. Both metals reflect much of the beam and conduct heat quickly, so they need more energy than steel: slower speeds, more passes and precise focus. Solid gold engraves cleanly; silver marks can look faint and often benefit from oxidizing for contrast. Always test on scrap first.
Laser engraving gold and silver turns simple jewelry into personalized pieces: names on pendants, dates inside bands, handwriting on charms. But precious metals behave differently from steel. They're reflective, they spread heat quickly, and mistakes cost real money.
This guide explains how to engrave solid and plated gold and silver with a fiber laser, with starting settings, tips for contrast, and the mistakes to avoid. For the broader workflow, see our laser engraving jewelry guide.
Can you laser engrave gold?
Yes. A fiber laser engraves solid gold of all common karats, gold-filled pieces and gold plating. Gold reflects much of the 1064 nm beam and conducts heat well, so it needs more energy than stainless steel. Precise focus and a small lens make a big difference.
Can you laser engrave silver?
Yes, with a fiber laser. Sterling silver is even more conductive than gold, so marks can be shallow and light. Many engravers add contrast afterward by oxidizing the engraving or use slower, multi-pass settings for visible depth.
Diode and CO2 lasers can't engrave bare gold or silver in a practical way.
Solid, filled and plated: know what you're engraving
| Type | What it is | What happens when you engrave |
|---|---|---|
| Solid gold or silver | The same metal throughout | Engraving shows the same metal, just textured |
| Gold-filled | A thick gold layer bonded to a base metal | Light marks stay in gold; deep marks can expose the base |
| Gold or silver plated | A very thin layer over brass, copper or steel | The laser removes the plating and exposes the base metal |
| Vermeil | Gold plating over sterling silver | Engraving exposes the silver underneath |
Always confirm what a customer's piece is before engraving it.
Starting settings
These are starting points for a 30W fiber laser with a 110 mm lens. Precious metals vary by alloy and finish, so test on scrap of the same material first.
| Job | Power | Speed | Frequency | Hatch spacing | Passes |
|---|---|---|---|---|---|
| Gold, surface mark | 70 to 90% | 500 to 1,000 mm/s | 30 to 40 kHz | 0.02 mm | 1 to 3 |
| Gold, engrave | 90 to 100% | 200 to 600 mm/s | 30 to 40 kHz | 0.02 mm | 5 to 20 |
| Silver, mark | 80 to 100% | 300 to 800 mm/s | 30 to 40 kHz | 0.02 mm | 2 to 5 |
| Silver, engrave | 90 to 100% | 200 to 500 mm/s | 30 to 40 kHz | 0.015 to 0.02 mm | 10 to 30 |
| Plated piece, light mark | 30 to 60% | 1,000 to 2,000 mm/s | 30 to 50 kHz | 0.03 mm | 1 |
Lower-power lasers need slower speeds and more passes. Our fiber laser settings chart covers other metals.
Getting contrast on gold and silver
Unlike stainless steel, precious metals don't easily turn black under the laser. Options:
- Deeper engraving catches light and shadow, so text reads clearly.
- Textured fills with tight hatch spacing scatter light and look frosted against polished metal.
- Oxidizing silver with a liver of sulfur style solution darkens the engraving; polish the surface afterward so only the recess stays dark.
- Enamel or paint fill on deeper engravings adds color.
A MOPA laser gives finer control over finish on precious metals. See what a MOPA fiber laser is.
Tips for engraving precious metals
- Focus perfectly. On reflective metals, being slightly off focus can mean no mark at all. See how to focus a fiber laser.
- Use a small lens (70 or 110 mm) for higher power density.
- Fixture the piece. Small pendants move easily. A jig avoids ruined pieces.
- Clean first to remove polish compounds and fingerprints.
- Go deeper with passes, not power alone. Many moderate passes give cleaner results than one aggressive one.
- Collect metal dust if you engrave a lot of gold. Some jewelers capture it for refining.
Rings, pendants and charms
Rings need a ring chuck or rotary; see how to engrave a ring inside and outside. Flat pendants and charms are the easiest place to start, with a simple jig to hold them level.
Common problems
| Problem | Likely cause | Fix |
|---|---|---|
| No visible mark | Too fast or out of focus | Slow down, refocus, add passes |
| Very faint mark on silver | High reflectivity and conductivity | More passes, tighter hatch, oxidize after |
| Base metal showing | Engraved through plating | Use lighter settings or skip plated pieces |
| Discoloration around text | Too much heat | Raise speed, add cooling time between passes |
| Rough texture | Too much power per pass | Lower power, add passes |
Safety
Polished gold and silver reflect the invisible fiber beam strongly. Wear 1064 nm glasses with an appropriate OD rating, keep others away from open-frame machines, and extract fumes, especially from plated pieces. Our safety glasses guide explains what to buy.
If precious metal jewelry is central to your work, a higher-power or MOPA machine pays off. Our best laser engraver for jewelry picks compare suitable options.
Frequently asked questions
Can a fiber laser engrave gold?
Yes. Fiber lasers engrave solid gold, gold-filled and gold-plated pieces. Gold is reflective, so it needs more energy and precise focus than steel.
Can you laser engrave sterling silver?
Yes, with a fiber laser. Marks can look light, so use slower multi-pass settings or oxidize the engraving for contrast.
Will laser engraving damage gold plating?
It removes the plating where the laser marks, exposing the base metal. Light settings reduce this, but plating is always affected.
Why won't my laser mark silver?
Silver reflects and conducts heat very well. Check focus, slow down, add passes and use a smaller lens for more power density.
Can a diode laser engrave gold or silver?
Not bare gold or silver in any practical way. Diode lasers lack the right wavelength and power density for reflective precious metals.