FiberLaserLab

Fiber Laser Settings Chart: Power, Speed and Frequency by Material

By FiberLaserLab Editorial Team. Updated November 19, 2026.

Quick answer

Fiber laser settings depend on your power, lens and material, so use a chart only as a starting point. For a 30W Q-switched laser with a 110 to 150 mm lens, white marks on stainless start around 60 to 80% power at 1,000 to 2,000 mm/s, anodized aluminum around 30 to 60% at 1,500 to 3,000 mm/s, and deep engraving around 90 to 100% at 500 to 1,000 mm/s with many passes. Always run a test grid first.

A fiber laser settings chart saves time, but only if you use it the right way: as a place to start your test grid, not as final numbers. Two machines with the same wattage can behave differently because of the laser source, lens, focus and the exact material.

This page collects starting settings for the most common fiber laser jobs, explains what each setting does, and shows you how to adapt them to your machine.

How to use this chart

The values below assume:

  • A 30W Q-switched fiber laser
  • A 110 to 150 mm lens
  • Accurate focus on a clean surface

Adjust for your setup:

  • 20W: slow down roughly a third, or add passes.
  • 50W to 60W: you can usually speed up or use fewer passes.
  • Larger lens (200 to 300 mm): slow down or add power, because power density is lower. See fiber laser lens sizes.
  • MOPA: see the MOPA notes below.

Every value is a starting point. Run a test grid on scrap before engraving real items.

What each setting does

SettingWhat it controlsTurn it up forTurn it down for
Power (%)Energy per pulseDeeper, stronger marksLighter marks, less heat
Speed (mm/s)How fast the beam movesLess heat, lighter marksMore energy per area
Frequency (kHz)Pulses per secondSmoother, more heat-like marksStronger individual pulses, more removal
Hatch spacing (mm)Distance between fill linesFaster jobs, visible linesSmoother, more even fills
PassesRepeatsDepthSpeed
Pulse width (ns, MOPA only)Length of each pulseMore heat, more removalCleaner, finer marks

For a deeper explanation, see speed, power and frequency explained and hatch settings explained.

Metals

Material and finishPowerSpeed (mm/s)Frequency (kHz)Hatch (mm)Passes
Stainless steel, white60 to 80%1,000 to 2,00030 to 400.03 to 0.051
Stainless steel, black (anneal)30 to 60%100 to 300High end of range0.01 to 0.021
Stainless steel, deep90 to 100%500 to 1,00030 to 400.02 to 0.0310 to 50+
Anodized aluminum, white30 to 60%1,500 to 3,00030 to 600.03 to 0.051
Bare aluminum, mark70 to 90%800 to 1,50030 to 400.031 to 2
Brass, mark60 to 80%800 to 1,50030 to 400.031
Brass, deep90 to 100%500 to 1,00030 to 400.02 to 0.0310 to 30+
Copper, mark90 to 100%200 to 60030 to 400.022 to 5
Titanium, mark40 to 70%800 to 1,50030 to 600.031
Gold, engrave90 to 100%200 to 60030 to 400.025 to 20
Silver, engrave90 to 100%200 to 50030 to 400.015 to 0.0210 to 30
Powder-coated tumbler70 to 90%1,000 to 2,00030 to 400.03 to 0.051 + clean pass
Painted or coated metal40 to 70%1,000 to 2,00030 to 400.031

Material guides with more detail: stainless steel, aluminum, brass and copper and titanium.

Non-metals

MaterialPowerSpeed (mm/s)Frequency (kHz)Hatch (mm)Notes
Black ABS20 to 40%1,000 to 2,00030 to 600.03 to 0.05Light mark
Polycarbonate20 to 40%1,000 to 2,00030 to 600.03 to 0.05Often darkens
Two-tone engraving sheet20 to 50%1,000 to 2,00030 to 600.03 to 0.05Use fiber-rated sheet
Hardwood, light mark20 to 40%1,000 to 2,00030 to 600.05 to 0.08Fiber isn't ideal for wood
Black granite50 to 80%800 to 1,50030 to 400.03 to 0.05Light marks
LeatherNot recommendedUse CO2 or diode

Never laser PVC, vinyl, PTFE or unknown plastics.

MOPA settings notes

MOPA lasers add pulse width control. Common starting approaches:

  • Black on stainless and dark marks on anodized aluminum: short pulse widths (around 2 to 20 ns) with high frequency (200 kHz and up).
  • Color on stainless and titanium: vary pulse width and frequency in a test grid. See color laser marking.
  • Plastics: short pulses for cleaner marks with less melting.
  • Deep engraving: longer pulse widths, similar to Q-switched settings.

How to run a test grid

  1. Create a grid of small squares (for example 5 x 5).
  2. Vary power across rows and speed across columns.
  3. Keep frequency and hatch fixed for the first grid.
  4. Engrave on scrap of the exact same material.
  5. Pick the best square, then run a second grid around it, varying frequency or hatch.
  6. Save the winner as a named material preset.

Most software, including EZCAD and LightBurn, can generate parameter grids automatically. See the EZCAD beginner's guide.

How to run a test grid 1 Create a grid of small squares (for example 5 x 5). 2 Vary power across rows and speed across columns. 3 Keep frequency and hatch fixed for the first grid. 4 Engrave on scrap of the exact same material. 5 Pick the best square, then run a second grid around it, varying frequency or hatch. 6 Save the winner as a named material preset.
A visual recap of the section "How to run a test grid" above.

Safety

Higher power and slower speeds mean more heat, fumes and reflections. Wear 1064 nm glasses rated for your laser, run extraction, and stay with the machine during every job.

Settings always depend on the machine in front of you. If you are still choosing one, our guide to the best fiber laser engraver for metal lists the power, lens and focus options to look at.

Frequently asked questions

What are good fiber laser settings for stainless steel?

For white marks on a 30W laser, start around 60 to 80% power, 1,000 to 2,000 mm/s and 30 to 40 kHz. Test before using them on real parts.

What frequency should I use on a fiber laser?

Around 30 to 40 kHz is a common starting point for marking and engraving. Higher frequencies help with annealing and smooth dark marks.

Why don't the settings from a chart work on my laser?

Laser source, lens, focus, material and calibration all vary. Use charts as a starting point and refine with a test grid.

How do I adjust settings for a 20W fiber laser?

Slow down by roughly a third or add passes compared with 30W settings. Test to fine-tune.

What hatch spacing should I use?

For most fills, 0.02 to 0.05 mm. Tighter spacing gives smoother results but takes longer.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.