FiberLaserLab

How to Laser Engrave Aluminum (Bare and Anodized)

By FiberLaserLab Editorial Team. Updated November 18, 2026.

Quick answer

To laser engrave aluminum, use a fiber laser, clean the surface, focus accurately and run a test grid. On anodized aluminum, a fast, moderate-power pass removes the dye for a crisp white mark. On bare aluminum, slower passes or more power create grey to white marks and real depth. MOPA lasers can also produce darker marks on anodized aluminum.

Aluminum is everywhere in engraving: anodized business cards, phone cases, flashlights, keychains, nameplates, tool handles and machine parts. It's an easy material for a fiber laser, but bare and anodized aluminum behave very differently. Here's how to handle each.

Bare vs anodized aluminum

Anodized aluminum has a hard oxide layer on the surface, usually dyed a color. The laser removes or bleaches this thin layer, revealing bright aluminum underneath. It needs very little energy and gives high-contrast results.

Bare aluminum has no coating. The laser has to mark or remove the metal itself. Marks are usually grey to white, and deep engraving is possible with more power and passes.

Which lasers work?

LaserAnodized aluminumBare aluminum
Fiber (Q-switched)Excellent white marksGood marks and deep engraving
Fiber (MOPA)White, grey and dark marksGood marks and deep engraving
DiodeGood white marksPoor without spray
CO2Good white marksNeeds marking spray

A fiber laser handles both. If you're comparing options, see what diode lasers can do on metal.

Which lasers work? Laser Anodized aluminum Bare aluminum Fiber (Q-switched) Excellent white marks Good marks and deep engraving Fiber (MOPA) White, grey and dark marks Good marks and deep engraving Diode Good white marks Poor without spray CO2 Good white marks Needs marking spray
A visual recap of the section "Which lasers work?" above.

Step-by-step

1. Clean and prep

Wipe the surface with isopropyl alcohol to remove oils and fingerprints. Remove protective film unless you're testing with it.

2. Focus carefully

Anodized layers are thin, so focus affects the sharpness of white marks. Use your machine's focus gauge or red-dot alignment. If you're new to galvo machines, read how galvo lasers work.

3. Run a test grid

Engrave a grid of small squares at different power and speed values. Anodized aluminum often marks well across a wide range, so you're looking for the cleanest, brightest white without burning.

4. Starting points

These are starting points for a typical 30W Q-switched fiber laser. Test before using on real items.

JobPowerSpeedFrequencyHatch spacingPasses
Anodized, white mark30 to 60%1,500 to 3,000 mm/s30 to 60 kHz0.03 to 0.05 mm1
Bare aluminum, light mark70 to 90%800 to 1,500 mm/s30 to 40 kHz0.03 mm1 to 2
Bare aluminum, deep engrave90 to 100%500 to 1,000 mm/s30 to 40 kHz0.02 to 0.03 mm10+

Lower power machines need slower speeds or more passes. More detail is in our fiber laser settings chart.

5. Clean up

Wipe off residue after engraving. On deep engravings, a fast, low-power cleaning pass helps remove debris and brighten the result.

Getting the best white on anodized aluminum

  • Don't overpower it. Too much energy can turn the mark grey or rough.
  • Use tight hatch spacing for solid fills without visible lines.
  • Try two passes at lower power instead of one high-power pass if you see uneven color.
  • Check the dye color. Some colors, especially red, may leave a faint tint and need an extra pass.

Getting dark marks on anodized aluminum

Standard Q-switched fiber lasers mainly produce white or silver marks on anodized aluminum. MOPA lasers can produce dark grey to black marks by using very short pulses and high frequencies. If dark marks matter for your products, read what a MOPA laser can do.

Common problems

ProblemLikely causeFix
Grey instead of whiteToo much powerLower power or increase speed
Patchy fillHatch too wide or out of focusTighten hatch and refocus
Faint color left behindDye not fully removedAdd a second light pass
Rough deep engravingToo few passes, too much powerLower power, add passes, alternate hatch angles

What to engrave next

Once you're comfortable with aluminum, stainless steel is a natural next step. Follow our guide on how to laser engrave stainless steel. If you're still choosing a machine, our picks for the best laser engraver for aluminum compare the options.

Safety when engraving aluminum

Wear safety glasses rated for 1064 nm on a fiber laser, and run extraction: anodizing dyes and coatings produce fumes, and bare aluminum produces fine particles. Polished aluminum reflects the beam, so avoid angled shiny surfaces that could send reflections across the room. See the laser engraver safety guide.

Aluminum project ideas

  • Anodized business cards and keychains
  • Flashlight and multitool personalization
  • Nameplates and asset tags
  • Phone and tablet accessories
  • Water bottles and drinkware

Frequently asked questions

Can you laser engrave aluminum?

Yes. Fiber lasers engrave both bare and anodized aluminum. Diode and CO2 lasers mark anodized aluminum well but struggle with bare aluminum.

Why is my engraving on anodized aluminum grey?

Usually too much power. Lower the power or increase the speed for a cleaner white mark.

Can a fiber laser make black marks on aluminum?

On anodized aluminum, a MOPA fiber laser can produce dark grey to black marks. Q-switched lasers mostly create white marks.

Is engraving aluminum safe?

Yes, with ventilation and proper 1064 nm safety glasses. Anodized dyes and coatings produce fumes, so always extract them.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.