How to Focus a Fiber Laser (Quick and Accurate Methods)
Quick answer
To focus a fiber laser, raise or lower the galvo head until the lens sits at its focal distance from the material surface. Use the machine's focus gauge, its two red dots that merge into one, or autofocus. For exact focus, run a ramp or step test and set the height where the mark is sharpest and brightest. Refocus whenever the item's height or the lens changes.
Knowing how to focus a fiber laser is the single most important skill for good marks. A focused beam concentrates its energy into a tiny spot; a few millimeters off and the same laser looks weak, blurry and inconsistent. Most "my laser isn't strong enough" problems are focus problems.
This guide explains focal distance, the common focusing methods, how to find exact focus with a test, when to defocus on purpose, and how to troubleshoot.
What focus means on a galvo fiber laser
On a galvo machine, the beam passes through an F-theta lens that focuses it at a fixed distance below the lens. That distance is the focal length (or working distance). Your job is to set the height of the galvo head so the material surface sits exactly at that point.
The focal distance depends on your lens. A 110 mm lens sits much lower than a 300 mm lens. See fiber laser lens sizes for how lens size changes focus height.
Why focus matters so much
| Focus | Spot size | Result |
|---|---|---|
| In focus | Smallest | Sharp edges, strongest marks, deepest engraving |
| Slightly out (1 to 2 mm) | Larger | Softer, lighter marks; sometimes useful for annealing |
| Far out (5 mm+) | Much larger | Weak, blurry or no mark |
Because power density falls quickly as the spot grows, a small focus error has a big effect.
Method 1: Focus gauge or ruler
Many machines come with a gauge, ruler or spacer cut to the correct distance:
- Place the gauge on the material.
- Lower the head until the lens (or a reference point on the head) just touches the gauge.
- Remove the gauge and lock the head.
It's quick and repeatable, but only as accurate as the gauge and its reference point.
Method 2: Dual red dots
Some machines have two red pointers that shine at angles. When the head is at the correct height, the two dots meet in one point:
- Turn on the focus pointers.
- Raise or lower the head until the dots overlap.
- Lock the head.
This is common and convenient, but the dots may need calibration. If they meet but marks look soft, verify with a ramp test.
Method 3: Autofocus
Some newer fiber lasers and enclosed machines measure the surface height and move the head automatically. It's fast, especially for mixed-height items. Check its accuracy occasionally with a test, and be aware that very reflective or curved surfaces can confuse some sensors.
Finding exact focus with a ramp or step test
The most reliable way to find true focus:
Ramp test
- Place a flat strip of scrap metal under the lens, raised at one end so its height changes gradually across the field.
- Mark a line or series of lines along it.
- Look for the sharpest, brightest or darkest part of the line.
- Measure the height at that point; that's your true focal distance.
Step test
- Set the head a few millimeters above your expected focus.
- Mark a small square.
- Lower the head by 0.5 or 1 mm, move the part slightly and mark again.
- Repeat through the expected focal point.
- The cleanest, strongest square marks true focus.
Record the result and adjust your gauge or red dots to match.
When to defocus on purpose
Defocusing spreads the beam over a larger area:
- Black annealing on stainless: a slight defocus (about 1 to 2 mm) can give smoother, more even dark marks. See black marking stainless steel.
- Wood and soft materials: defocusing can reduce scorching.
- Cleaning passes: a slightly defocused fast pass can clean residue.
Always test defocus amounts rather than guessing.
Focusing on curved and deep items
- Tumblers and rings: focus on the top of the curve, then use a rotary so the focus line stays at the top. See the rotary attachment guide.
- Uneven surfaces: focus on the area you'll mark; anything far above or below will mark weaker.
- Deep engraving: as the engraving gets deeper, lower the head by roughly the depth already removed so focus stays at the bottom. See how deep a fiber laser can engrave.
Troubleshooting focus problems
| Symptom | Likely cause | Fix |
|---|---|---|
| Weak marks across the whole design | Out of focus | Refocus; verify with a step test |
| Strong in center, weak at edges | Part not flat, or lens field edge effects | Level the part, keep it near center |
| Red dots meet but marks are soft | Dots misaligned | Calibrate dots to true focus |
| Focus changes during long jobs | Head slipping | Tighten the column lock |
| Marks differ after a lens change | New focal distance | Refocus and re-test |
If marks are still weak after focusing, see why a fiber laser isn't marking.
Safety
Never adjust focus while the laser is firing. Wear 1064 nm glasses during tests, and keep hands out of the work area when pressing Mark. If you're new to the workflow, our guide on how to use a laser engraver covers the full first-job process.
Focus is easier on machines with autofocus. Our best fiber laser engraver for metal comparison lists the focus type of each model, and the best laser engraver for beginners guide does the same for starter machines.
Frequently asked questions
How do I know if my fiber laser is in focus?
Run a step or ramp test. The sharpest, strongest mark shows true focus. Many machines also use a gauge or two red dots that meet at focus.
What is the focal distance of a fiber laser?
It depends on the lens. Larger lenses have longer focal distances. Check your manual or measure it with a step test.
Why are my fiber laser marks blurry?
Usually focus is off. Refocus, check the part is flat and confirm with a step test.
Should I defocus for black marking?
A slight defocus of about 1 to 2 mm often helps with smooth black annealing on stainless steel. Test to find the best value for your machine.
Do I need to refocus for every job?
Refocus whenever the height of your item changes, after a lens change, or if marks look weaker than usual.