FiberLaserLab

Hatch Settings Explained: Line Spacing, Angles and Fill Types

By FiberLaserLab Editorial Team. Updated November 20, 2026.

Quick answer

Laser hatch settings control how a fiber laser fills a shape with lines. Line spacing (often 0.02 to 0.05 mm) sets smoothness, angle sets the line direction, crosshatch adds a second angle, bidirectional fill speeds things up, and border offset keeps edges clean. For deep engraving, rotate the hatch angle every pass to avoid ridges. Tighter spacing looks smoother but takes longer.

Laser hatch settings are where good fiber laser marks become great ones. Two jobs with the same power and speed can look completely different because of hatch spacing, angle and fill type. If you see visible lines, uneven fills or ridges in deep engraving, the hatch is usually the reason.

This guide explains each hatch setting in EZCAD and LightBurn, starting values, and how to fix common problems.

What is a hatch?

A hatch is a set of parallel lines the laser uses to fill a closed shape, like letters or a logo. Instead of scanning the whole field like a printer, a galvo laser fills each shape with lines that stop and start at the shape's edges. See raster vs vector engraving for how this compares with other fill methods.

The main hatch settings

SettingWhat it doesTypical starting value
Line spacing (interval)Distance between hatch lines0.02 to 0.05 mm
AngleDirection of the lines0° or 45°
Crosshatch / multiple hatchesAdds lines at another angleSecond hatch at 90°
BidirectionalLines go back and forth instead of one directionOn for speed
Border offset (edge offset)Gap between hatch lines and the outline0 to 0.02 mm
Outline (contour)Traces the shape's edge after fillingOn for crisp edges
Auto-rotate angleChanges angle each passOn for deep engraving
Loop countNumber of passes1 for marks, many for depth
Hatch spacing and angle Too wide Visible stripes Right range Even fill Too tight Burned fill Typical starting spacing: 0.02 to 0.05 mm. 0° 45° 90° 135°
Line spacing changes how the fill looks. For deep engraving, rotate the hatch angle each pass.

Line spacing: the most important setting

Line spacing decides how smooth the fill looks:

  • Too wide: you see stripes, and marks look lighter.
  • About right: smooth, even fill.
  • Too tight: the job takes longer, heat builds up, and stainless steel can discolor.

A useful rule is to keep spacing around or slightly below your spot size. For most desktop fiber lasers with a 110 to 150 mm lens, 0.02 to 0.05 mm works well. Black annealing on stainless often needs tighter spacing, around 0.01 to 0.02 mm. See black marking stainless steel.

Angle and crosshatch

  • Single hatch at 0° or 45°: fine for most marks.
  • Crosshatch (two hatches, e.g. 0° and 90°): gives a more even fill, especially on larger areas. It doubles the marking time.
  • Angle choice: sometimes changing the angle reduces visible lines on brushed or textured surfaces. Hatching at an angle to the brushed grain can look more even.

Bidirectional vs unidirectional

  • Bidirectional: the laser marks in both directions, saving time.
  • Unidirectional: every line goes the same way. It can give more consistent fills, especially if your machine's delays aren't perfectly tuned.

If you see slightly ragged edges with bidirectional fill, try unidirectional or adjust the machine's delay settings.

Border offset and outline

A small border offset stops hatch lines from overlapping the outline, which avoids extra-dark or burned edges. Adding an outline pass after the fill sharpens the shape's edge, especially for text and logos.

Hatch settings for deep engraving

Deep engraving is where hatch settings matter most:

  1. Rotate the angle each pass (for example 0°, 45°, 90°, 135°, repeat). This prevents ridges from building up along one direction.
  2. Use moderate spacing, around 0.02 to 0.03 mm.
  3. Add a cleaning pass every 10 to 20 passes: fast, low power, tight spacing.
  4. Keep the outline off for most passes, then add it at the end if you want sharp edges.

See how deep a fiber laser can engrave.

Fill types in EZCAD and LightBurn

EZCAD offers several hatch types, such as unidirectional, bidirectional, ring-like (follows the shape's outline inward), and optimized fills. LightBurn offers similar fill options plus features like crosshatch and fill grouping. Ring-like fills can look good on simple shapes but may be slower.

Our guides to EZCAD and LightBurn for galvo lasers show where each setting is.

Starting hatch values by job

These are starting points. Combine them with power and speed values from the fiber laser settings chart, and test.

JobSpacingAngleCrosshatchOther
White mark on stainless0.03 to 0.05 mm0° or 45°OptionalOutline on
Black anneal on stainless0.01 to 0.02 mm0°OffSlight defocus can help
Anodized aluminum0.03 to 0.05 mm45°OptionalOutline on
Deep engraving0.02 to 0.03 mmRotate each passBuilt in by rotationCleaning passes
Plastics0.03 to 0.05 mm0°OffLow heat

Fixing hatch problems

ProblemLikely causeFix
Visible stripesSpacing too wideReduce spacing
Burned or discolored fillSpacing too tight or too much heatIncrease spacing, raise speed
Ridges in deep engravingSame angle every passRotate angle each pass
Dark or burned edgesHatch overlaps outlineAdd border offset
Ragged line endsBidirectional fill with untuned delaysTry unidirectional or adjust delays
Uneven fill on brushed metalHatch parallel to grainChange angle or crosshatch

Safety

Tighter spacing and more passes mean more heat and longer jobs. Keep extraction running and wear 1064 nm glasses.

Hatch and fill options live in your software, so if you have not settled on a program yet, read LightBurn vs EZCAD for fiber lasers. The best fiber laser engraver for metal guide notes which software each machine includes.

Frequently asked questions

What hatch spacing should I use on a fiber laser?

For most fills, 0.02 to 0.05 mm. Black annealing often needs 0.01 to 0.02 mm, and deep engraving works well around 0.02 to 0.03 mm.

What does crosshatch do in laser engraving?

It adds a second set of fill lines at another angle, which gives a more even fill but takes longer.

Why does my laser engraving have lines in it?

Hatch spacing is usually too wide, or focus is off. Tighten spacing and check focus.

What hatch angle is best for deep engraving?

Rotate the angle each pass, for example in 45° steps, so ridges don't build up.

What is border offset in hatch settings?

A small gap between the fill lines and the outline that prevents extra-dark or burned edges.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.