FiberLaserLab

Laser Engraving File Formats: SVG, DXF, PNG and More

By FiberLaserLab Editorial Team. Updated November 20, 2026.

Quick answer

The best laser engraving files are vector formats like SVG, DXF, AI and PDF for logos, text and cutting, and high-resolution PNG or JPG for photos. Convert text to curves, close open paths, remove duplicate lines and size the design to the item before engraving. Fiber lasers in EZCAD favor DXF and PLT; LightBurn opens most common formats.

Laser engraving files decide how clean your result looks before you even touch the settings. A crisp vector logo engraves with sharp edges; a small, blurry JPG gives fuzzy text no matter how good your laser is.

This guide explains the common file types, which to use for each job, how to prepare files, and where to get designs.

Vector vs raster files

VectorRaster (bitmap)
What it storesLines, curves and shapesA grid of pixels
ScalingAny size without losing qualityGets blurry when enlarged
Best forLogos, text, outlines, cutting, hatch fillsPhotos and shaded images
Common formatsSVG, DXF, AI, EPS, PDF, PLTPNG, JPG, BMP, TIFF

For how the laser treats each type, see raster vs vector engraving.

Vector vs raster files Vector Raster (bitmap) What it stores Lines, curves and shapes A grid of pixels Scaling Any size without losing quality Gets blurry when enlarged Best for Logos, text, outlines, cutting, hatch fills Photos and shaded images Common formats SVG, DXF, AI, EPS, PDF, PLT PNG, JPG, BMP, TIFF
A visual recap of the section "Vector vs raster files" above.

Common file formats

FormatTypeNotes
SVGVectorWidely supported, great for logos and text; LightBurn handles it well
DXFVectorCAD standard; very reliable in EZCAD and for cutting files
AIVectorAdobe Illustrator; save in an older or compatible version if import fails
EPSVectorOlder format, still common for logos
PDFVector or rasterCan contain either; check that logos are real vectors
PLTVectorPlotter format, well supported by EZCAD
PNGRasterGood for photos and images with transparency
JPGRasterFine for photos; avoid for logos due to compression artifacts
BMPRasterSimple, widely supported in EZCAD

Which file should you use?

JobBest file
Logos and textSVG, DXF, AI or PDF (vector)
Serial numbers and QR codesCreated directly in your software
PhotosHigh-resolution PNG or JPG
Cutting (CO2, diode, thin metal on fiber)DXF or SVG
Customer-supplied logosAsk for SVG, AI, EPS or PDF

Software compatibility

  • EZCAD: imports DXF, PLT, AI (some versions), and bitmaps like BMP, JPG and PNG. DXF is usually the most reliable for vectors. See the EZCAD beginner's guide.
  • LightBurn: imports SVG, DXF, AI, PDF, EPS, PNG, JPG, BMP and more. See LightBurn for galvo lasers.
  • Manufacturer apps (such as xTool Creative Space) support common formats like SVG, DXF, PNG and JPG.

How to prepare files for laser engraving

1. Convert text to curves

Fonts may not exist on the computer running the laser. Convert text to outlines or curves in your design software so it engraves exactly as designed.

2. Close open paths

Hatch fills only work on closed shapes. Open paths engrave as lines or not at all.

3. Remove duplicates and overlaps

Duplicate lines get engraved twice, which can burn deeper or leave marks. Use your software's tools to remove duplicates and combine overlapping shapes.

4. Size the design to the item

Measure the item with calipers and set the design to its real size in millimeters.

5. Simplify very complex files

Files with thousands of tiny nodes can slow software and cause jerky motion. Simplify curves where possible.

6. Check image resolution

For photos, use enough pixels for the engraving size. At 300 DPI, a 50 mm wide image needs about 590 pixels across. Our guide to laser engraving photos covers editing and dithering.

Turning a JPG logo into a vector

If a customer only has a JPG or PNG logo:

  1. Use the trace function in LightBurn, Inkscape or Illustrator.
  2. Adjust the threshold until the shapes look clean.
  3. Delete stray points and fix curves.
  4. Compare with the original at full size.

For complex logos, ask the customer for an original vector file or redraw it.

Where to get laser engraving files

  • Create your own in Inkscape (free), Illustrator, Affinity Designer or LightBurn.
  • Buy designs from marketplaces that sell laser-ready files, and check the license allows commercial use.
  • Customer files: ask for vector versions of logos.

Respect copyright: don't engrave trademarks, characters or logos you don't have rights to use, especially on products you sell.

Common file problems

ProblemLikely causeFix
Text engraves as outlinesNot filled or not closedClose paths and apply hatch fill
Fuzzy logo edgesLow-resolution rasterUse a vector or trace the image
Design imports at the wrong sizeUnit mismatchCheck mm vs inch on export and import
Lines engrave twiceDuplicate pathsRemove duplicates
Missing parts of designUnsupported effects or embedded imagesFlatten, expand or convert to paths

Safety

File prep doesn't change laser safety: wear wavelength-rated glasses and ventilate during every job. When files are ready, see how to use a laser engraver for the full workflow.

The formats you can use depend on your software. See the best laser engraving software and LightBurn vs EZCAD if you are choosing a program.

Frequently asked questions

What file type is best for laser engraving?

Vector files like SVG, DXF, AI or PDF for logos, text and cutting. High-resolution PNG or JPG for photos.

Can you laser engrave a JPG?

Yes, as a raster engraving. For logos and text, a vector file gives sharper edges.

What file does EZCAD use?

EZCAD saves jobs as EZD and imports DXF, PLT and common bitmaps. DXF is usually the most reliable vector format for it.

Does LightBurn accept SVG files?

Yes. LightBurn imports SVG, DXF, AI, PDF, PNG, JPG and other common formats.

How do I convert an image to a laser file?

Use a trace tool in LightBurn, Inkscape or Illustrator to turn the image into vectors, then clean up the result.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.