FiberLaserLab

Laser Engraving Titanium: Colors, Settings and Uses

By FiberLaserLab Editorial Team. Updated November 16, 2026.

Quick answer

Laser engraving titanium is done with a fiber laser, which can produce light, dark or deep marks and vivid oxide colors like gold, blue and purple. Clean the part, focus precisely and run a test grid. MOPA lasers give the widest, most controllable color range, while Q-switched lasers handle standard marks and engraving well. Titanium engraves more slowly than aluminum.

Laser engraving titanium is popular for EDC gear, knife scales, pens, rings, watch parts and medical or aerospace components. Titanium is strong, light and corrosion-resistant, and with a fiber laser it can take crisp marks, real depth and some of the most striking oxide colors of any metal.

This guide covers which laser to use, how titanium colors form, starting settings and practical tips. If you're new to fiber lasers, read how to use a laser engraver first.

Which laser works on titanium?

LaserBare titaniumAnodized titanium
Fiber (Q-switched)Light, dark and deep marks; limited colorRemoves anodized color
Fiber (MOPA)All of the above plus a wide color rangeRemoves or alters color
Diode, CO2Not practical without marking sprayLimited

A 20W to 30W fiber laser marks titanium well. Higher power helps with deep engraving, which is slower on titanium than on brass or aluminum.

Which laser works on titanium? Laser Bare titanium Anodized titanium Fiber Q-switched Light, dark and deep marks; limited color Removes anodized color Fiber MOPA All of that, plus a wide color range Removes or alters color Diode, CO2 Not practical without marking spray Limited
What each laser type can do on bare and anodized titanium.

How titanium colors form

Like stainless steel, titanium forms a thin oxide layer when heated. Light interference in that layer creates color, and the layer's thickness decides which color appears. Titanium tends to produce bright, saturated colors, often more easily than stainless steel.

Typical progression as heat input rises: gold, bronze, purple, blue, light blue and other tones. Exact results depend on the alloy, finish and laser. For the same process on steel, see color laser marking stainless steel.

Starting settings

These are starting points for a 30W fiber laser with a 110 mm lens. Titanium alloys and finishes vary, so test first.

JobPowerSpeedFrequencyHatch spacingPasses
Light mark40 to 70%800 to 1,500 mm/s30 to 60 kHz0.03 mm1
Dark mark30 to 50%200 to 500 mm/sHigh end of range0.01 to 0.02 mm1
Color (MOPA)20 to 50%300 to 1,500 mm/s200 to 600 kHz, varied pulse width0.01 to 0.02 mm1
Deep engrave90 to 100%500 to 1,000 mm/s30 to 40 kHz0.02 to 0.03 mm20 to 100+

More materials are in the fiber laser settings chart, and the hatch settings guide explains spacing and angles.

Step by step

  1. Clean the part with isopropyl alcohol.
  2. Focus precisely. Color and dark marks are sensitive to focus.
  3. Run a test grid on scrap of the same alloy and finish.
  4. Mark near the lens center for consistent results.
  5. Control heat on small parts by pausing between areas, since heat buildup shifts colors.

Titanium grades and finishes

Most titanium you'll engrave is either commercially pure titanium (often called Grade 2) or the alloy Ti-6Al-4V (Grade 5), which is common in knife scales, EDC tools and aerospace parts. Both mark well, but colors and dark marks can shift between grades, so a color recipe built on one won't always transfer to the other.

Finish matters too. Bead-blasted titanium gives softer, more even marks, while polished titanium shows sharper contrast but reflects more of the beam. Stonewashed parts can look patchy, because the surface texture varies. Keep a labeled scrap piece of each grade and finish you work with.

Anodized titanium

Anodized titanium gets its color from an oxide layer grown electrically. The laser can remove that layer to reveal bare titanium, or heat it to change the color. Results vary, so test on the same anodized color before working on a finished piece.

Deep engraving titanium

Titanium removes more slowly than many metals and holds heat. Use many moderate passes, rotate the hatch angle each pass, add cleaning passes, and let parts cool between blocks. See how deep a fiber laser can engrave.

  • Rings and jewelry (see how to engrave a ring)
  • Knife scales and pocket clips
  • Pens, keychains and EDC tools
  • Watch cases and backs
  • Serial numbers on precision parts

Safety: titanium fire risk

Solid titanium parts are safe to engrave, but fine titanium dust and chips can ignite. Keep work areas clean, don't let titanium dust build up in your extractor or around the machine, and never use water on a metal fire. Wear 1064 nm glasses rated for your laser and run extraction. See the laser engraver fire safety guide.

If color work on titanium and steel matters to you, a MOPA laser is worth considering. See our best MOPA fiber laser picks.

Frequently asked questions

Can you laser engrave titanium?

Yes. A fiber laser engraves titanium with light, dark or deep marks, and can create vivid oxide colors.

What colors can a laser make on titanium?

Common colors include gold, bronze, purple and several blues. A MOPA laser gives the widest, most controllable range.

Is titanium hard to laser engrave?

Marking is easy. Deep engraving is slower than on aluminum or brass, and titanium holds heat, so parts need cooling breaks.

Can a diode laser engrave titanium?

Not bare titanium in a practical way. A fiber laser is the right tool.

Is laser engraving titanium safe?

Yes, for solid parts, with normal laser precautions. Avoid buildup of fine titanium dust, which is flammable.

FiberLaserLab Editorial Team
We research fiber, CO2 and diode lasers so you can choose and use the right machine with confidence. How we work.